Our company manufacturing strengthen type ultrafine mill is mainly used in the production of ore powder equipment, it can make the ore grinding to fine fineness can reach 2500, and if the user does not need such a fine material, can also be ground to 325 mesh, can be adjusted in 325 to 2500 between.There are so many ultrafine mills on the market, so what is the special advantage of the ultrafine mill that can attract so many customers?

First of all, the grinding material layer and multi round powder selection principle, and each rotor can be variable speed, the grinding fineness in the selected range does not require a grader can be realized, and energy saving than ordinary mill.

Secondly, the automation level of the machine is comparable to that of all kinds of intelligent operation systems, such as mechanical limit device and electronic limit device, roller press control mode, single lubrication station device, etc., which can easily monitor the mill production status, and is safe and reliable.

Moreover, the ultrafine mill pays special attention to the energy saving and environmental protection. Wear-resistant parts use high quality materials, save metal consumption, work under negative pressure, no dust overflow, and small vibration, low noise, meet the environmental requirements.

The new ultrafine mill is a new professional equipment in the ultra-fine milling industry. It has outstanding advantages in technology application, product quality, production efficiency, production cost, energy saving and environmental protection. It's your best choice.

In recent years, the amount of construction waste produced by urban construction has been increasing, and the annual emissions of construction waste are all tens of millions of tons. The emergence of a new type construction waste crusher helps to realize the recycling of building garbage. Before the construction waste disposal by landfill, in addition to the large consumptive field, occupy valuable land resources, energy consumption, pollution and other negative factors. Therefore, how to use it is imminent and social and highly technical problems need further.

The construction of garbage after crushing, sorting, crushing or eliminating waste, most can be used as the regenerate resources, such as scrap steel, scrap wire, scrap wire and various accessories such as scrap metal, after sorting, concentrated and re melted, can be manufactured into various specifications of steel; waste bamboo timber can used in the manufacture of artificial wood; brick, stone and concrete waste crushing, can replace sand, used in masonry mortar, plastering mortar, concrete cushion, and can also be used for making bricks, paving brick, brick and other building materials, lattice.

In the crushing process of building waste recycled fine aggregate, due to the physical characteristics of the material itself, the two stage crushing is usually used, and the particle size of the crushing product is 0-10mm, which accounts for about 25%. In order to improve the production of fine aggregate, it is a very effective means to use two stage breakage to break three stages and make most of the broken products less than 0-10. However, in the specific technology and technology, there are many problems, such as complex process, difficult process layout, large amount of electricity consumption and excessive investment.

To this end, the company based on the original equipment on the basis of many tests and improvements, the introduction of construction waste special model. The device can not only achieve multi-stage crushing, but also meet the needs of grain size regulation. It provides a perfect solution for building waste aggregate recycling and crushing process, and it is the best choice for construction waste crusher.

Ore milling equipment is one of the most important equipments in many mills. How to choose the right ore milling equipment is suitable for the mills. At present, green production and construction and environmental priority should be clinging to. So many companies committed. Enterprises that are unlawfully productive for the destruction of the environment are not only faced with a huge amount of environmental taxes, but also the punishment of stopping production. Therefore, the construction of green production line has become the most important part of the development of many enterprises.

For the grinding work of the enterprise, environmental protection tax, production and other issues have been naked in front of, dust pollution has been a failure as extremely serious pollution to the environment, not only pollute the atmosphere, the harm to human body is also very serious, dust inhalation will bring great harm to people's health.

Our ore milling equipment has no dust leaks and no pollution to the environment, and it has the following advantages.

Higher screening rate

Ore mill is a vertical structure, with a small area and complete set. Compared with other flour mills, the grinder has a higher screening rate, up to 99%, which is difficult for other grinding equipment to achieve.

Low cost of use

The main components of the ore grinding machine are all cast with high quality materials and fine technology, which ensures the high efficiency and good wear resistance of the whole set of ore grinding machine. In the process of operation, the wearable parts of the easily worn parts are good in wear resistance and long service life.

The electric system adopts centralized control, and the mill powder mill of the ore mill can basically realize the unmanned operation, and the maintenance is convenient.

Performance stability

The main engine of the ore mill has improved the traditional way, and made a stable structural transformation for the main shaft and the plum blossom rack, making the transmission stable and reliable.

Sand washing machine is a necessary equipment for sand washing machine. The sand washing machine can remove the stone powder and impurities from the mixed sand produced by the sand making mechanism, so as to improve the quality of the sand. It can also clean and separate dirt and debris from sand and gravel. Its new sealing structure, adjustable overflow weir plate and reliable driving device ensure the effect of cleaning and dewatering. It is mainly used for construction site, sand factory and hydropower station concrete dam workers.

1. The sand washing machine has unique sealing structure and reliable rotary device. We all know that the sand washing machine has the advantages of reasonable structure, convenient operation, large volume of processing, low power consumption, high cleanliness, and less sand loss during sand washing. The transmission parts of sand washing machine are all isolated from water and sand, which reduces wear. Besides screen mesh, there are basically no other vulnerable parts. It's an excellent choice for upgrading the sand washing industry in China.

2. The working principle of the sand washing machine and other sand washing machine, motor belt, sand washing machine gear reducer, gear reducer drives the impeller to rotate slowly, powder feed chute into the washing tank, roll driven impeller and grinding each other, removing impurities covering powder surface, while destruction vapor - coated sand layer, in order to facilitate the dehydration; while adding water, the strong water flow in the small proportion of impurities and foreign objects.

3. The effect of sand washing machine achieved by sand washing machine is better than that of other sand washing machines, and the cleanliness of stone powder washed by sand is high, which ensures the efficiency and quality.

Raymond mill is a commonly used grinding equipment in the quarry plant. Raymond mill is mainly suitable for processing mohs hardness below 7, humidity below 6% of all kinds of inflammable and explosive ore, such as gypsum, talc, calcite, limestone, marble, barite, dolomite, granite, kaolin clay, bauxite, iron oxide red, iron ore, etc.

Raymond mill is a mineral processing equipment commonly used in mineral processing equipment. It is also a high-energy equipment. The energy saving design and parameter optimization design of Raymond mill plant is of great significance to reduce energy consumption and improve the efficiency of mineral processing.

1. Strong systemic and high screening rate. The whole machine is a three-dimensional structure, which occupies a small area and has a strong system. It can form a separate production system from the raw material processing to the packaging of powder and powder. The fine fineness of finished product is uniform, and the sieve rate is as high as 99%.

2. Easy to control and easy to maintain. With the centralized control electrical system, the workshop can realize the unattended operation. The electromagnetic vibration feeder is used to feed the material, continuously and evenly, easy to adjust, save oil and power, and easy to maintain.

3. Stable transmission and high wear resistance. The machine transmission device adopts the closed gear box and the belt wheel, the transmission is stable, the operation is reliable. The core components adopt high - performance wear-resistant materials, high wear resistance and cost saving.

In the process of using ultrafine grinder, we need to improve its usage, so that we can make users more perfect and get the recognition of users. But how do you improve the use of the pulverizer? The appearance of ultrafine mill is a major technological breakthrough in the industry of grinding powder. Its grinding operation makes the grinding work of some more difficult materials to be realized, and the user needs to be used. So it's a gratifying thing.

However, a good product always has its defects. In view of the shortcomings of the ultrafine mill, we need to summarize it, then make relevant improvement work, so that it can better meet people's usage habits and use requirements. In the process of grinding, it also has a lot of shortcomings, let's look at it.

In order to make the grinding equipment more enjoyable, we need to know enough about it before operation, then we can better operate it, make it play a better state and produce better products. During the period of production, it is necessary to do a good job of maintenance, which is a quick and effective way to keep the machine's high performance.

Between the use, better to carry out a comprehensive inspection, check the work is essential. Reasonable inspection work can reduce some of the problems in the work, so that the problem can be effectively solved. After the use of the machine, we should always pay attention to the use of the machine, which is the premise to ensure the ultrafine mill can achieve good work.

Therefore, the user should check that all the fasteners are fastened. Check that the transmission belt is installed correctly and in good condition. If the belt damage is found, it should be replaced in time. When there is oil contamination on the belt or grooved wheel, clean it up and wipe it in time. Check the hydraulic hoisting head or hoisting rod back, adjust whether the pad is correct and pressed. Check whether there is any material or other sundries in the damaged cavity, if it should be cleaned up sometimes. Check the protective device is good, if the protective device is unsafe, it should be eliminated in time.

For the use state of ultrafine grinder, its transformation should be carried out reasonably. We can maintain regular treatment for him, so that it can get greater productivity and get better production status and create greater value for users. In the same way, the superfine pulverizer itself has achieved its own great value.

Sand making machine is one of the most commonly used equipment for building sand. Sand making machine is suitable for soft or hard and super hard materials, widely used in all kinds of ores, cement, refractories, aluminum where soil clinker, carborundum, glass raw materials, mechanism building sand, construction aggregate, artificial sand and various metallurgical slag crushing and coarse grinding, especially for silicon carbide, carborundum, sintered bauxite, the sand high hard, and very hard abrasive resistant material than other types of crusher yield higher efficiencies.

In the field of engineering, it is an ideal production equipment for the mechanism sand, the cushion material, the asphalt concrete and the cement concrete aggregate. In the field of mining, sand making machine is widely used in the process of grinding before grinding, which can produce a large amount of powder ore and reduce the high cost of grinding load.

The stone fell into the high-speed rotating wheel directly from the upper part of the machine, in high speed under the action of centrifugal force, and the other part of the umbrella type high speed way of diversion in the wheel around the target of stone impact and high density of crushed stone in the fight against each other, will form a vortex motion between the turntable and the chassis caused by repeated against each other, rubbing and crushing, direct discharge from the bottom. A closed circuit multiple cycle is formed, which is controlled by the screening equipment to reach the required granularity.

Characteristic：
1. A small amount of easy wear parts are made of very hard and wear-resistant material, small in volume, light in weight and easy to replace.
2. The structure is novel, unique and smooth.
3. the energy consumption is small, the output is high, and the crushing ratio is large.
4. The equipment is small in volume, easy to operate, easy to install and maintain.
5. it has plastic function, the product is cubic and the packing density is big.
6. in the process of production, the stone material can form the protection of the bottom, the fuselage is not worn and durable.

The new ultrafine grinding equipment developed by our company includes crushing, lapping, conveying, lifting and dusting. The fineness of flour can be adjusted arbitrarily between 250 mesh -3000, and its performance has reached the leading level of the market. In the ultra fine mill technological innovation we are constantly working hard. Save a lot of trouble clients can automatic equipment of ultrafine mill, and does not require a large number of personnel equipment; company of vulnerable devices using ultra wear resistant material, can greatly reduce the vulnerability of the replacement frequency; facing serious environmental problems, our company joined the baghouse powder grinding machine full set of equipment in the ultrafine, effective to prevent excessive dust emissions caused by air pollution.

What is the improvement of ultrafine mill compared with the ordinary grinding machine?

1. high efficiency, energy saving and low running cost: when the fineness and motor power of the product are the same, the output is more than twice higher than that of the airflow mill, stirring mill and ball mill. Both the grinding roll and the grinding disc are used for the special wear resistant castings and the international surfacing technology. The service life is longer, which reduces the metal pollution of the products and reduces the operating cost. The equipment has an external circulation device, which can further reduce the power consumption and improve the precision of the product.

2. The long life of the damaged parts is long: the grinding roller and grinding ring are made of special materials, so that the use degree is greatly improved. Under the same material and finished product fineness, the service life of worn parts of impact crusher and turbine grinder is 2-5 times longer than that of ordinary crusher, which usually reaches more than one year. When processing calcium carbonate and calcite, the service life can reach 2-5 years.

3. high safety and reliability: because there is no rolling bearing and no screws in the grinding chamber, there is no problem of the bearing and its seals being vulnerable. There is no problem that the screws are easy to loose and destroy the machine.

4. The quality of the product is stable and the fineness of the product is high. The material has short residence time in the vertical ultrafine grinding machine, and it is easy to detect and control the particle size and chemical composition of the product. The machine has a high-precision classifier, which can be classified into 325 mesh to 6000 products. The grading accuracy is high, the cutting particle is accurate, and the product quality is stable. Ultrafine powder grinding fineness can reach D97 disposable products less than or equal to 5 mu m.

5. the operation is safe, easy, reliable, and convenient to repair. The device is equipped with a direct contact device between the roller sleeve and the grinding disc liner, which does not cause destructive severe vibration, and improves the service life of the roller sleeve and the grinding disc. It is a new industrial flour mill. The rollers and linings can be replaced in a very short time by overhaul the cylinder

6. The area is small. The ultrafine grinder system integrates crushing, grinding and grading transportation. Compared with the ball mill system, the floor area can be reduced by about half, which greatly reduces the construction cost.

In the development of science and technology, mineral processing equipment also began a new round of reform, whether it is business or sand washing machine, a variety of devices are beginning to improve. With the development of technology and technology, the details are the key to the sand washing machine. This is also a problem that the manufacturer of sand washing machine should pay attention to in the future development. But most of the time people tend to focus on the important aspects and ignore the details, but the details are the key to the success or failure.

In order to meet the development of the times, the road of the transformation of sand washing machine is imminent. In the wave of improvement, if we want to have our stable customer resources in the international market and occupy a certain position in the mineral processing equipment, we must learn from the experience and lessons of the domestic mineral processing equipment and sand washing machine.

At first, many foreign sand washing equipments were stationed in our market, which brought great stimulation to our sand washing machine. Therefore, we should pay more attention to every detail. From pre - use to use, we should do a good job of inspection and maintenance. Before using, we must know clearly the structure and working principle of the sand washing machine before we can operate the machine. Besides, we need to check if there are any defects in the components of the sand washing machine. In use, we need to do a repair to the sand washing machine, because only in this way can we use it better. Specifically, such as spiral rotation, and then feeding slurry, volume of ore gradually increase. If the sand washing machine is in working state encountered special faults such as stuck, overload, must stop immediately, while the spiral ascending out of the pulp side, will never permit spiral pressure in the pulp, to avoid blockage, to quickly mine valve open, start again, will spiral down to a certain position to turn, spiral, is the only way we can guarantee the safe use of the sand washing machine.

The Raymond mill's production efficiency has been one of the factors of production of the manufacturers are concerned about the user, in the use of Raymond Mill powder machine, we are very concerned about the efficiency of it, the milling equipment is equipment for the production of fine powder mill, the production efficiency effect, plays an irreplaceable role, but the production efficiency, user it is always expected to have better performance.

When the Raymond mill working, it will also consider all kinds of production factors in it so that it can receive better effect. Therefore, the manufacturers from the selection of materials, structural design and other factors, the research of the machine is very deep. In order to enable users to get satisfactory production results, many large manufacturers often carry out dozens or even hundreds of experiments, and get the right production data to ensure the production of users.

For the user, we should pay more attention to the operation in order to make the machine better serve us. So, in the process of using, we should pay attention to the problem of Raymond Mill powder feeding machine, to achieve uniform when feeding, and no impurities mixed, especially solid impurities, such as iron, because it will not only threaten the quality of production, and safe use of the mill also caused great effect.

When users operate, they should pay attention to the dynamics of the machine. When they have a large vibration, they must be shut down. In the place of vibration, the staff should tighten or take other effective measures to reduce the damage caused by the vibration.

It is necessary to pay attention to the staff of the Raymond mill. In the process of production, the user should check the fineness and production efficiency of the material, and then make some related adjustments so that it can reach a better production state.

In addition, many users suggest that appropriate maintenance can also improve production efficiency to a certain extent. It is true that maintenance has a great relationship with the working state of the machine. In the process of use, Raymond mill can increase production if it can get a suitable maintenance plan.

So, as the user of the mill, we have to carry out proper maintenance in accordance with the characteristics of the machine so that the Raymond mill can perform better performance.